E-Classic Roof LED Bulb/Plug Assembly Replacement (P/N 10486)
$67.95This LED bulb/plug assembly (p/n 10486) is the replacement light component for the roof panel on E-Classic 1400, 1450, 2400, and 3200 models.
Showing 201–240 of 344 results

This LED bulb/plug assembly (p/n 10486) is the replacement light component for the roof panel on E-Classic 1400, 1450, 2400, and 3200 models.

This optional stainless steel elbow (p/n 1200488) is the replacement for the secondary air intake on E-Classic 1400, 2300, 2400, and 3200 models .

This kit (p/n 2500047) protects the transformer in E-Classic models from short circuits.

This flat shovel (p/n 2900535) is specifically designed to remove ash from the back of the Reaction Chamber on E−Classic and Classic Edge models .

This 5-pack of 5−A fuses (p/n 6648) is the recommended replacement for electrical protection in Dual Fuel furnace models .

This kit provides a UPS battery back-up (p/n 2500005), wiring, relay, and brackets to power the burner auger for emergency clean out in M175 or M250/M255 P models .

This Refractory (p/n 4050001) is one of two upper refractory pieces required for the E-Classic 1450, and requires 4 ft of rope (p/n 7674).

This replacement burn chamber gasket (Dimensions: 1/4 ′′ ×7−7/8 ′′ W×7−3/8 ′′ H) is essential for the M250/255P models.

This 3/4 ′′ x 2 ′′ extra-heavy MPT nipple (p/n 533) is used for plumbing connections with pumps and ball valves .

The Stainless Steel Air Channel Kit Front (p/n 2500293) is for Classic Edge 550 models with serial number G501253 and up .

This fan (p/n 322) is the replacement air-moving component for the 100k Btu Suspended Space Heater.

The Cast Door Lock Kit (p/n 537-011) prevents unauthorized firebox access on various Cam Loc models, including the CL 6048/CL 7260 cast-iron door .


High-temperature firebrick for E-Classic Reaction Chambers. Available in various sizes to fit specific models. Essential for maintaining thermal integrity and protecting the furnace structure.

This Power Supply Kit (p/n 2500678) is the replacement power supply for the FireStar controller on Classic Edge, CleanFire, and Forge models .

This non-adjustable, immersible aquastat is factory-set at 175 ∘ F and features a 1/2 ′′ MPT fitting .

This non-adjustable, immersible aquastat is factory-set at 190 ∘ F and features a 1/2 ′′ MPT fitting .

The Line Voltage Thermostat (120-volt) is used to initiate the fan in forced-air systems.

This Ground Rod Kit (p/n 6593) is used to properly and safely electrically ground the furnace .

This sensor well (p/n 5958) houses and protects the separate Temperature Sensor Probe p/n 727 used with the Digital Temperature Controller .

These louvers (p/n 355) bolt onto the face of the p/n 106 Heat Exchanger Coil to direct heated air flow downward .


Replacement heat shields for cast firebox doors on Classic outdoor furnaces. Protects the outer door from intense heat. Sold individually; two required per door.

This 5-pack of 5/8 ′′ −11 x 2 ′′ short-neck carriage bolts (p/n 5924) is a replacement component used for securing assemblies .

This 24-inch Braided Flexible Hose (3/4 ′′ ×24 ′′ ) creates flexible and durable plumbing connections on the furnace.

The Brass FIP Ball Valve (p/n 410) provides on/off flow control for 1−1/4 ′′ pipe connections .

This 180−205 ∘ F snap disc (p/n 8200000) is the replacement water jacket high-limit sensor for various Classic Edge, CleanFire, Forge, and some E-Classic/Maxim models .

This 100% silicone adhesive is rated to 500 ∘ F and is primarily used to secure the door sealing rope .

This O-Ring (p/n 5000397) is the replacement seal for the Hot Filter (p/n 101) and Cartridge #10 (p/n 202) assembly .

This is the #10 Hot Filter cartridge replacement only (p/n 202) for the filter assembly .

This immersible aquastat (p/n 191) controls pool and spa water temperature between 40−180 ∘ F and should be used with a separate stainless steel well .

Optional dial temperature gauges are available as the standard p/n 174 (1/2 ′′ MPT) or the compact p/n 6054 (1/8 ′′ MPT) for tight area installation .


Replacement isolation auger motors for Maxim furnaces. Includes gasket. Available for M175 (2.0 RPM) and M250/M255 series (4.1 RPM).

This p/n 5000472 3/4 ′′ lead-free Backflow Preventer is used to protect water supplies from contamination .

This 3/4 ′′ NPT lead−free thermostatic mixing valve (p/n 5000392) is designed specifically for water heaters, with a 90 ∘ F−130 ∘ F range.

This set provides two essential replacement O-Ring Gaskets for Taco Pump Flanges.

This LED Temperature Display (p/n 1999) is the replacement unit for older outdoor furnaces with serial numbers up to 13427 .

This p/n 1497 LED Temperature Display requires the p/n 1496 Transformer to convert 110V AC to 12V DC.

This light switch kit (p/n 187) is a replacement component that includes the cover plate and seal .

This is the Litmus Paper (p/n 153) component only, used with discontinued water test kits (p/n 405/597) to measure water pH .

This 1/15 HP Blower & Motor assembly (p/n 203) is a replacement component for low-power air circulation applications .

This 24-volt transformer (p/n 188) is used to power 24-volt wall thermostats and zone valves.
No products in the cart.